WEAN UNITED ELECTROLYTIC GALVANIZING LINE 1985 

Used secondhand 72 inch Electro Galvanizing Line

ELECTROLYTIC GALVANIZING LINE
Manufacturer: Wean United
Year of installation: 1985
Year of Shutdown: 2014
Yearly production: 360,000 Ton per year (2,000lb/ton) 327, 000 Metric Ton
Product information: 98% automotive exposed; Not able to process todays’ high strength materials and is not capable to process Alloy material; can only process Zinc material)
Minimum Maximum Width: 28 inch (610 mm) to 73 inch (1828 mm)
Minimum and Maximum Thickness: 0.0200 inch – 0.0800 inch ( 0.500 mm – 2 mm)
Cross Section Restriction: 4.6 Sq in Maximum

Entry Coil ID: 24 inch (610 mm)
Entry coil OD Minimum: 36 inch (915 mm)
Entry coil OD Maximum: 98 inch (2500 mm)
Entry Coil footage: 2500 feet (762 meters)
Entry Coil Weight: 140,000 lb (63.5 Metric Ton)

Delivery Coil ID: 20 and 24 inch (508 mm – 610 mm)
Delivery Coil OD Minimum: 30 inch (915 mm)
Delivery Coil OD: 80 inch (2032 mm)
Delivery Coil Weight: 70,000 lb. (32 meric Ton)
Delivery Winding Direction: Over or under wound

Coating weight GI 30-150g/mm2
Coating Weight GA: 30-60 g/mm2
Differential Coating Weight Available
Surface Finish: Lead Free Bath (No Spangle) Galvanize (GI) and Galanneal (GA)
Normal (not Skin passed/skin passed0

Post Treatment: Tension Leveling
Chemical Treatment (chromate Passivation)
Chemical Treatment (Phosphate Coating)

Oiling: Normal Quaker 61AUS
Pre-Lube Montgomery 7105A

Heat Buckle index (Width/Gauge): CQ/CS/FS – 2700 Max
DDQ/DDS – 2500 Max
EDDQ/EDDS – 2500 Max
All others – 2600 Max

Major List of Equipment

1. One (1) Payoff Reel with Snubber Roll
2. No. 1 Pinch Roll
3. One (1) Payoff Reel with Snubber Roll
4. No. 2 pinch Roll
5. No. 1 and 2 Entry Thickness Gage
6. No. 1 and 2 Entry Shears
7. Scrap gate and Chutes
8. No. 1 Entry Deflector Roll
9. Converging Conveyors
10. Prep Lap Welder
11. Entry Pinch Roll
12. No. 1 Cleaning Section
13. No. 2 Cleaning Section
14. No. 3 Cleaning Section
15. Rinse Section
16. Strip Dryer Heater
17. No. 1 Bridle Rolls
18. No. 1 Roll at the Entry Looper
19. 16 Strand Entry looper
20. No. 2 Steering unit
21. Weld Detector Arrangement
22. Strip Sensor Arrangement
23. Entry Bridle for Tension Leveler
24. Tension Leveler
25. Exit Bridle for Tension Leveler
26. Deflector Roll
27. Earthing Roll
28. Two (2) Alkaline Cleaning Tanks
29. No. 1 Scrubber unit
30. One (1) Pickling Tank
31. No. 1 Rinse Tank
32. No. 2 Scrubber Unit
33. Steering Roll Unit
34. Wetting Tank
35. Thirteen (13) Plating Tanks (1 to 13)
36. Steering Roll Unit
37. Seven (7) Plating Tanks 14 to 20)
38. No. 2 Rinse Tank
39. No. 3 Scrubber unit
40. Surface Conditioning Tank
41. Two (2) Hot Rinse Tanks
42. Hot Air Dryer
43. Deflector Roll with Earthing
44. Coating Thickness Gage
45. Strip Support Table
46. Entry Bridle Rolls for Exit Looper
47. No. 3 Steering unit
48. Exit Looper
49. No. 4 Steering unit
50. Weld Detector
51. Visual inspection
52. No. 1 and no. 2 Strip Printer
53. Exit Bridle Rolls (Roll 1 and 2)
54. Bridle Tables
55. Exit Bridle rolls (Roll 3 and 4)
56. Exit thickness Gage
57. Exit Pinch Roll
58. Electrostatic oiler
59. Exit Down Cut shear
60. No. 1 Exit Edge guide
61. No. 1 Deflector Roll
62. No. 1 Tension Reel (Recoiler) with coil car
63. No. 2 Exit Edge Guide
64. No. 2 Deflector Roll
65. No. 2 Tension Reel (Recoiler) with coil car

Note: Specification and List of Equipment is prepared on the based of available information.

Ref. No. BPMB818151