70TON/HOUR (500,000TPY) REBAR MILL

 

 

Used second hand70ton/hour (500,000TPY) Rebar mill in Japan
Rebar Mill(and round bar)
Capacity: 70ton/hour 
Site area: 80,673m2
Rolling mill factory area: 7164m2(26m x255m)
Product stock yard area:18m x 87m
 
Comissioning year: 1974
Capacity: 70ton~75ton /hour=approx.500,000ton/year
(approx. 24hour x 330days/year run)
Product: D10/D13
*If these are made by new rolls, the rebar ,diameter 40mm can be produced
 
(Electric supply)
3300V
110KV
Contract supply electric(at night):5800kwh
 
(Gas supply)
Supply calori:46MJ
Pipe dia.:150A
Pressure:0.2Mpa
Max.capacity:4500m3/h
 
(Water supply)
Capacity:Industrial water 100m3/h
Pressure:0.1Mpa
 
(Billet heating furnace)
Make:Furnast(Japan)
Year:1997
-3 girdle continuous type
-Avaliable length:21m
-Inside width:4.8m
-Capacity:75ton/hour
-Fuel:gas
 
(Rolling mills)
Make:Hitachi, IHI(Japan)
Rolling mill stand manufacturing year: 1973 /1982/1985
Roll manufacturing year:/2003/2004/2009/2011/2015
 
Roughing mill:360mm~390mm x900mmL : 7 sets
Intermidiate mill:325mm x900mmL :4 sets
Finishing mill:360mm x800mmL :10sets
Capacity:70ton~75ton/hr
 
(Refining process)
Year:2007
Capacity: 75ton/hour
Cooling table: 9m x95m
Cutter:2 stopper type, all automatic
Binding:
automatic small binding machine: 4sets
automatic Large binding machine: 2sets
 
(Plant Upgrades)
1. Ductile roll purchase: about 40sets, 2015
2. High speed cutting machine purchase: 2014
3. Sycro reduction gear: replace with new one
(Make: Sumitomo: Japan), 2014
4. Rebar cutting machine purchase, 2014
5. Billet heater side pusher: replace with new one,2012
6. New brand roll purchase: about 40sets,2011
7. Roll :replaced with new one(Make:Hitachi), 2009
8. Electric supply station: upgrade,2008
9.SCR cutting machine: 2008
10. Universal testing machine: replace with new one, 2008
11. Traverser electric : replace with new one, 2008
12. Refining equipment: replace with new one, 2007
13. Billet heater fuel system: replace with new one, 2007
14. Roll : replaced with new one(Make:Mitsubishi), 2004
15. Run out table: upgrade, 2004
16. Billet cutting automatic carrier : 2004/2005
17. Roll : replaced with new one(Make:Hitachi), 2003
18. Binding machine: replace with new one, 2003
19. Cutting machine: replace with new one, 2003
20. Control panel: replaced with new one, 2003
(Make: Sinko:Japan, CPU)
21. 80ton weight sclaes: replace with new one, 2003
22. Crane(No.3,No.4) remote controller upgrade: 2003
23. Crane(No.2) digital contrlller upgrade: 2003
24. Billet heater: replaced with new one, 1997
(Blower motor 132KW, 2P, 3300V)
25. Rolling mill outlet roller guide: replace with new one, 1997
26. Rolling mill inlet roller guide: replace with new one, 1997
27. Finishing line electric: replace with new one, 1997
28. Rolling mill spindle: replace with new one, 1995
29. Geared type ring reduction gear: replace with new one, 1995
30. AC SERVO type: replaced with new one, 1994
31. Rolling mill stand shift(No.17,No.18):
replace with new one, 1994
32. Billet heater entrance upgrade: 1993
33. Cold shear: replace with new one, 1993
34. Electric room : replace with new one, 1993
35. Finishing mill upgrade: 1993
36. Line table: replace with new one, 1991
37. Line table electric : replace with new one, 1991
38. Automatic cutting machine: replace with new one, 1991
39. Dust collector : replace with new one, 1990
40. Table loader: replace with new one, 1986
41. Finishing roll stand(Number15~Number 20):
replaced with new one, 1985
42. Roughing mill roll stand(number1~number 6):
replaced with new one, 1982

 

 

 

Ref. No. BPMB101832